六合在线

当前位置:六合在线 - 新闻动态 > 企业动态 >

多功能电脑弹簧机在编程的过程中如何解决问题?

来源: http://www.chinahzrx.com    时间:2019-07-18 14:36:54 作者:山东银丰弹簧机设备

当遇到安装编程无法归零的现象也缺乏为怪,主要的是检查设备是不是处于正常状态。消费弹簧的原理主要是应用反作用力,送线轮把钢丝送向前方,在钢丝前方用线规挡住,使钢丝不能向前,产生阻力,改动钢丝的运动方向,使钢丝产生相关的外形。
When encountering the phenomenon that installation programming can not return to zero, it is not surprising that the main thing is to check whether the equipment is in normal condition. The principle of consumption spring is mainly to apply reaction force. The wire feeding wheel feeds the wire forward, and the wire gauge is used to block the wire in front of the wire, so that the wire can not move forward, produce resistance, change the moving direction of the wire, and make the wire have the relevant shape.
处理办法及步骤:
Procedures and steps:
1。驱动器参数问题(这仅限于机械制造厂内部工作思索),若机器每次归零后的零点位置均不在同一点,则思索电子齿龄比设定能否正确。
1. Driver parameters (this is limited to the internal work of the mechanical factory), if the zero position of the machine after each return to zero is not at the same point, then consider whether the setting of electronic tooth age ratio is correct.
2。察看多功用电脑弹簧机银幕右上角的一黄色三角信号灯能否有反向动作,察看银幕状态。将作正常的归零动作。若有,则可能为电路板损坏;若无反向动作,或做归零动作时偶然会反向,那就请翻开机器后盖,重做归零动作,察看近接开关指示灯能否会在机器运转一周的过程中正常闪亮一次。如不能正常闪亮,可将近接开关拿在手上,在机器归零过程中,直接去与机器接触,若近接开关为仍不亮,则检查近接开关接在电路板上的插头能否接触不良,否则可断定近接开关自身毛病。
2. See if a yellow triangular signal lamp in the upper right corner of the screen of the multi-function computer spring machine can move backwards and check the screen status. Normal return to zero action will be performed. If yes, the circuit board may be damaged; if there is no reverse action, or if there is occasional reverse action when doing zero action, please open the back cover of the machine and do zero action again to see if the proximity switch indicator will normally shine once in the course of a week's operation of the machine. If it can't shine normally, you can hold the proximity switch in your hand. In the process of machine zero, you can contact the machine directly. If the proximity switch is still not bright, you can check whether the plug of the proximity switch connected to the circuit board is not in good contact, otherwise you can judge the proximity switch's own fault.
备注:
Remarks:
1。多功用电脑弹簧机运转中,制止用手接触面板。弹簧产品的掉落一定要控制好方向,以免卡住刀座,发作撞机现象,弹簧产品有异常时必需中止后才停止调整修正。
1. In the operation of multi-function computer spring machine, it is forbidden to touch the panel by hand. The drop of spring products must be well controlled so as not to jam the tool holder and cause collision. When spring products are abnormal, they must be stopped before adjustment and correction can be stopped.
电脑弹簧机
2。弹簧消费设备的构造为主轴箱、电脑显现屏,成型区,伺服电机,刀具,轴心,自动送线架,液压区等。主轴箱及螺距区由伺服电机经过减速来带动主轴转动,或者纵向平移。
2. The structure of spring consumption equipment is spindle box, computer display screen, forming area, servo motor, cutter, axle center, automatic wire feeding frame, hydraulic area, etc. The spindle box and pitch area are driven by the servo motor through deceleration to rotate the spindle, or to move longitudinally.
3。由于多功用电脑弹簧机的原理不同于其他设备,操作时需求留意以下内容:开机要按严厉按运用步骤,消费前必需检查调机时调动的一切紧固件,以免在消费中松动、掉落、移位,发作撞机现象,招致机器损伤。
3. Because the principle of multi-function computer spring machine is different from other equipment, the following should be noticed when operating: Start the machine strictly according to the application steps, before consumption, it is necessary to check all fasteners mobilized during shunting, in order to avoid loosening, falling, shifting in consumption, occurrence of collision phenomenon, causing machine damage.
针对于以上的资讯,你有没有什么不同的意见呢?欢迎您致电我们或者点击我们的网站电脑弹簧机http://www.chinahzrx.com参与讨论!
Do you have any different opinions on the above information? Welcome to call us or click on our website computer spring machine http://www.chinahzrx.com to participate in the discussion!

上一篇:弹簧机的发展能解决哪些弹簧的生产问题?
下一篇:弹簧试验机带给弹簧哪些使用?
联系我们

六合在线 分分时时彩 五分时时彩 六合在线 分分时时彩 六合在线 六合在线 五分时时彩计划 六合在线 六合在线